Quality Importers HUM-3DR The Palermo 3 Drawer Cigar Humidor Holds up to 150 Cigars

You will have to come up with a way to seal the gaps between the drawers in order to keep the humidity levels stable. There are 1/8" gaps between the three drawers that allow the humidity to escape. This makes it an impossibility to keep your humidor seasoned and, well humid. I have found that you will need to go to your local hardware store and purchase a weather strip material and apply it to the bottom of the peice over your drawers. This method keeps the weather strip out of sight and maintains the units classy good looks.

Great looking design that was not thought through enough. If you are not handy enough to be able to fix this issue, I would not recommend purchasing this unit.

Honeywell Easy to Care Cool Mist Humidifier, HCM-750

Last fall I purchased a Honeywell HCM750 cool vapor humidifier, made by Kaz. Initially it worked fine but, following its instructions, after a couple of weeks I cleaned it. When I put it back together, it would not run and had to phone Kaz customer service. I am quite handy with these gadgets and followed their instructions but could not get it to work; it appears the core of the humidifier is a magnetic rotor that makes the fan turn and it just would not work.

Finally I sent the unit back for repair/replacement, and since it was winter and wanted to keep the humidity in my house at an appropriate level, I purchased a second unit, which I figured later on to use in the bedrooms area. It was around Christmas time, but it took three weeks to get the repaired unit back. Once back it worked fine, and I kept both units going. When both were working, my electronic temperature and humidity control was measuring between 25 and 30%, which I consider on the low end of humidity during the winter months, with gas hot-forced-air heating, and I kept the units runnning 24-7, except when adding water to the tanks.

A few weeks later it was time to clean both units and lo and behold, one of them would not run and had to play with the magnetic rotor for maybe one hour or so until it would start running properly. Put both units back to work, and the next day, one of them is sitting in a 12-inch poodle of water. Could not figure out what was the problem; took it apart, put it back together, and then again problem with the magnetic rotor. Finally got it to work only at medium speed (it has a 3-speed dial).

By this time I was quite disappointed and decided to take both units and donate them to a non-profit organization, while looking to buy another brand for next winter. Sorry I bought it. I will do better next time.

We should have researched before purchasing this humidifier. It worked fine for a couple nights, then randomly stopped working. We played around with the assembly of the tubing and got it to work, only to have it break down again a few nights later. We ultimately returned the unit, assuming it was defective, only to get a brand new one that also stops working on a regular basis.

In short, I would NOT recommend this humidifier to anyone who wants a reliable unit that you know, actually functions. If you want to tinker with it for hours on end, then this is for you.

Buy Honeywell Easy to Care Cool Mist Humidifier, HCM-750 Now

This humidifier worked fine for a few weeks, then the pump failed. I called up customer service and they sent a new pump. It ran another month and now this pump is failing. It's a poor design, the bushing on the pump rotor wears out and the pump rotor jams. I'm replacing the pump with a small table-top fountain pump. These last much longer under continuous use.

Read Best Reviews of Honeywell Easy to Care Cool Mist Humidifier, HCM-750 Here

After using this product for about 6 months, and letting it run dry a time or two, I found that, as others have noted, the pump would lock up (with a loud "clack") and the water would stop flowing. I disassembled the pump and tried various fixes involving washers, but my thinnest washer was still too thick to let the impeller spin.

I then had the idea of lubricating the impeller and the inside of the pump. I didn't have any silicone spray, but I did have a candle I used for fragrance. Smearing a fingertip with the oily wax, I wiped the wax all over the impeller, the removeable cap, and the inside of the pump, and reassembled the pump. Voila! No more locking up. This worked until I accidentally let the pump run dry again; after relubricating it it's working fine again.

This is an easy fix for the only problem I've found in what is otherwise a great product. I particularly like the fact that filling the humidifier with water is very easy and requires no disassembly; you can just pour it into the large openings even while the unit is running. Also, the wicking is clearly visible at the top of the unit so that you can tell that all's well with it.

Want Honeywell Easy to Care Cool Mist Humidifier, HCM-750 Discount?

We bought one of these near the end of November and were initially happy with it. I read some of the other reviews out here; we didn't have any issues with the motor, and didn't find it particularly noisy. It worked well for about two months. I took it apart and put the washable pieces through the dishwasher on a few occasions. The humidity in the house was finally hovering around 35-40%. No problems so far.

The other day, I decided to relocate it. I picked it up and there was a huge wet spot on the carpet where it had been sitting. No good. I cleaned it again, and set it on a plastic lid from a storage container. Sure enough, the next day it was sitting in a puddle of water.

I called Honeywell product support, they said it was defective and wanted me to ship it back to them at my expense. I told them I didn't have the box anymore and it would be cheaper for me to just toss it and buy a new one. Mwa waaa.

Pros: works well, not particularly noisy, kicks out plenty of moisture (as long as you fill it once a day).

Cons: leaks like crazy although there are no apparent cracks in the water containing portion of the unit. Maybe it isn't a leak, I suppose the warm motor could attract some condensation but I doubt it.

We threw it out. Buy something else.

Save 57% Off

Aprilaire Model 600 Automatic Whole-house Bypass Humidifier with Digital Control

• The Aprilaire 600 Automatic Humidifier replaces the, now discontinued, Model 600A
• The Aprilaire 600 Automatic Humidifier includes the Model 60 digital control with blower activation
• Unit is truly automatic when connected to Model 60 Digital Control and, included, outdoor sensor
• Also Includes: Aprilaire Model 35 water panel, 110V to 24V transformer, and built-in bypass damper
• This unit has a water feed rate of 3.0 GPH and will deliver an evaporative rate of 0.70 GPH

This is my 3rd Aprilaire 600 and they were all worth every penny. (The 600 used to be called the 600A, now both are automatic and the 600's electronics are slightly updated.) The 600 can be switched to manual mode, if desired.

My first unit was in my last house and was run for 2 years with no issues, then we moved. I just installed 2 in my current house (since I have 2 furnaces, 1 for each floor). I set it to humidity level #5 out of 7, which sets the relative humidity to 35% when the outdoor temperature is about 20 degrees F (details in the manual). The unit automatically turns on when the furnace is running and there is a call for more humidity. The unit can turn on your furnace blower in order to add humidity even when the furnace is not running, but I didn't want that option, so I didn't wire it in. If you do wire it in, there is a switch on the control unit so that you can turn it on or off.

Pros

* It's automatic and comes with an outdoor temperature sensor. This allows the unit to automatically adjust the humidity level so that you don't get condensation on your windows (condensation and the associated mold growth are why some home inspectors do not recommend humidifiers.)

* For us, it reduces nose bleeds and sinus infections.

* No standing water for mold to grow in. No individual room units to clean and refill.

* Works great, turn it on as the weather starts to get cold (also turn on the water to it and turn the lever to open the built in damper) and turn it off as the weather warms up.

* Low maintenance: Replace the water panel 1 time per year

* Low repair costs: There's no fan or extraneous parts. The only moving part is the valve that turns on and off the water. The value is quick and cheap to replace if it ever builds up enough sediment or mineralization to impede function.

* Low upkeep: The manual says to replace the water distribution tray and valve solenoid every ~5 years. All the parts are easy to access and relatively cheap. After 2 years my original water distribution tray showed no wear and I don't think it will really need to be replaced.

* Integrates with the electrical power in your furnace, so there's no extra wiring (assuming your furnace is new enough to have the jumpers.)

* Completely silent.

* Uses almost no electricity

* I did not notice a decrease in air flow coming out of vents throughout the house.

* Easy to install if you are handy. Our local Heating guys charge about $450 to install these and it only takes them 2 hours. I did it myself in about 4-6 hours. All the tools you really need are sheet metal snips, a good drill to put in sheet metal screws, a wrench for tightening plumbing connections, wire strippers, and ideally a 3/4" metal drill bit to install the electronic control. Installation instructions are included in the box, including wiring instructions. The instructions aren't idiot proof, but they're easy to follow for a handy person.

Cons

* Some water is wasted as unevaporated water does drain out the bottom. While I don't want water wasted, I actually think this is a preferable design. I don't want to waste electricity heating the water to create steam and I don't want a tray of standing water for mold or bacteria to grow in (the 400 model has a tray of standing water and no drain, but is otherwise the same as the 600.) I haven't noticed a change in my water bill since installing these units.

* A drain is required. I directed mine into my air conditioner's condensation drain which feeds to the sump pump. No problem. It it's a problem for you, try the 400 model.

Function

The unit works by taking air that has been heated by your furnace and passes it through a panel that has a small amount of water running across it. The water panel looks a bit like a radiator. The water on the panel evaporates into the hot air and gets distributed through your existing ductwork. That's it, nothing fancy. Note that, just like any humidifier, the unit is more efficient if you connect it to hot water rather than cold.

If you decide to install it yourself and go against the recommendation to have a professional do it, you'll also need the following:

#8 sheet metal screws

1/4" copper water line

1/2" ID clear vinyl tubing for drain

Clamp to attach the vinyl drain tubing to the humidifier

Small wire nuts

6" start collar for bypass connection

6" 90 degree elbow(s) for bypass connection

6" pipe for bypass connection

18-2 thermostat wire (a few feet of 18-5 may be helpful to go between the humidifier and your furnace, but 18-2 will work there as well)

Depending on your furnace, 2 quick disconnect electrical plugs may be needed to connect the included transformer to your furnace's power.

If furnace circuit board does not include humidifier accessory terminals an Aprilaire #50 Current Sensing Relay will be needed.

Optional Duct tape (don't use fabric tape, UL rated foil backed tape will last much longer and won't burn) or mastic will improve heating efficiency.

Optional you may want to feed the vinyl drain tubing inside a 3/4" PVC drain to make sure if doesn't get damaged or knocked out of your drain.

Buy Aprilaire Model 600 Automatic Whole-house Bypass Humidifier with Digital Control Now

Aprilaire Model 600 Automatic Whole-house Bypass Humidifier with Digital ControlThis is a highly sophisticated humidifier. I consider myself to be a fairly handy homeowner but after receiving the item and reading the directions I opted to pay a professional for the install. I am glad that I did. I had estimates in my area to do the install between $250 and $350 over the cost of the unit.

Everything on this unit is automatic. A hard wire runs outside of the house to monitor the outside air temperature.

The only question that I had before I bought the unit was weather the 3 gallons per hour of water ran 24/7 or not. The answer is that it does not. A solenoid only lets the water run when the unit needs to add humidity.

I am more satisfied with this product than I expected to be.

Read Best Reviews of Aprilaire Model 600 Automatic Whole-house Bypass Humidifier with Digital Control Here

It's a great product and it works extremely well when set to full automatic. The outdoor temperature sensor needs to be installed for automatic mode for proper relative humidity and to avoid window condensation. Yeah it takes some time to install it properly but well worth it. When it's set to automatic it will actually kick on your blower periodically even without a call for heat to get an accurate check of the humidity levels and stay on if they are low. The automatic mode helps tremendously after the heat runs and it needs to stay on for a bit to keep the levels accurate. I also found this setup to be useful in reducing cold spots in the house and to help maintain even temperatures kind of like a 2-stage furnace would. With a flip of a switch it can be set to manual and will only run if there is a call for heat and humidity is required. If you're going to spend the time to install one of these, I wouldn't settle for a unit that is not automatic. The 24vac transformer that was sent with the unit was pretty cheap; I tried to loosen one of the terminals and it broke the lead. Not worth a phone call so I just picked up one at the hardware store for $13. If you plan on using this for automatic purposes, then the transformer should be powered with constant power. I ran power down from the furnace power switch to the blower compartment where I mounted the transformer. That's also nice because when you shut down the furnace via the switch it also shuts down the humidifier and adds protection with the onboard furnace fuse. You will want to wire the transformer at the switch and not from any wires or furnace electronics after the switch (excluding a designed HUM accessory power lead). Like many others my furnace's Honeywell circuit board is equipped with a HUM accessory power lead and on my unit it is 120V so don't think you can bypass the use of a transformer if that's the case. But if your board is similar to mine the HUM power lead will only work if you plan on using it in manual mode as it's only powered when there is a call for heat; it is not powered when there is only a call for the blower or no call at all. Obviously the unit will be more efficient when supplied with heated air; as will be the case most of the time. But there are several studies that show a sufficient amount of humidity will be applied by just the blower moving ambient air through the unit. The manual does state that when set to automatic mode then the unit should be supplied with hot water and in general that is a good practice for the MOST efficient way to evaporate water and help keep the impurities from building up over time. But I couldn't justify the usage of energy that it takes to make that water hot and watch it go down the drain. Some studies show that the benefit is insignificant in supplying hot water over cold water. It's going to be up to you but I couldn't do it and the unit still works very well when supplied with cold water. Hope this helps some of you out in the decision process and I posted a few pictures of the install.

Want Aprilaire Model 600 Automatic Whole-house Bypass Humidifier with Digital Control Discount?

So like others mentioned... the install guide(s) are a bit crude. Install took me just over 3hrs to do. I piggy backed of the 24v supply already there for the furnace. Used the hot water line for best performance. The tough spots were tin snipping the openings (now i have increadible grip strength) and fitting the 6" flex duct hose (must be a trick to it i don't know) to the unit and the flange. Make sure your sheet metal screws are long enough as mounting holes on the unit are raised. I used an earlier review which had a check list of supplies needed for this project and for once didn't have to make two trips to the hardware store (thanks!).

Some tips: To get the unit to work without the temp sensor in place make sure you select manual on the Digital controller (otherwise water won't flow and error message will show). Make sure you get enough wire (@ $.23 a foot better to have extra then to waste gas and time going back). Finally make sure you are at least 6" upstream from your unit with the Control mounting otherwise you will get higher moisture readings.

I was able to turn down the temp in the house 2 degrees and still felt it was too hot in the house (2,500sqft). I am sure i will be getting returns on this for a long time not to mention how pleasant the house feels.

Aprilaire Model 600 Automatic Whole-house Bypass Humidifier with Digital Control

Save 40% Off

The humidity hasn't been low enough yet to actually run this yet so I can't comment on its effectiveness (will update review later). However, installation was fairly easy if you are somewhat handy. Wiring in to furnace was a breeze with included wiring diagram. I mounted the 24VAC transformer in a junction box on the side of the furnace. I installed the unit on the cold air return due to concerns raised in other reviews about water dripping down in to the furnace. I opted to not use the saddle valve and chop my hot water pipe and solder in a T with a ball valve instead (not a fan of saddle valves).

Kids Line Ultrasonic Cool Mist Humidifier

Check the water tank size on the description and compare b4 u buy. I didn't expect it to be this small. Even the cord is extra short; about 3 feet. I think you'll be disappointed if you live in a dry climate and plan to use this a lot. Water level indicator is also a tiny window and hard to see.

The picture is misleading and obviously photo-manipulated because it shows the 3 mists all going up. Real product has one nozzle pointing up and back, and two on the sides pointing parallel to the floor. So if you have anything directly adjacent to it, it will become soaked.

I also have the Crane "Drop"-shape humidifier; much bigger tank and cute for kid's room as well.

This was not a good product. It leaked all over. The water leaked out of the side and eventually flooded the stand we placed it on. Tried a few different places to place it and still had the same problem. Looks better than it works.

Buy Kids Line Ultrasonic Cool Mist Humidifier Now

We just received this today (12/03/2011) as a Baby Registry gift from our friends. This cool mist humidifier is very cute and it's made with very good material, we just love it. Here's how we got it to work, super easy. My wife just opened the package, filled up the water tank, put it back, plugged in the power, and turned it on, that's it. The cool mist then just started to come out on top of the monkey's head and both of his ears.

I was a little worry about this Kids Line Humidifier before because I read reviews from another web site stating that this model leaks water, but there is no water leaking at all, it works perfectly and safely. I bought a Crane Humidifier a month ago, and we had to return it because it didn't work. The major differences between the Kids Line Humidifier and Crane Humidifier is that the way the water tank is designed. After we filled water inside the tank, we have to turn the water tank upside down in order to put it back. Here lies the huge problem with the Crane models, the water from inside would come pouring out onto the bottom part of the humidifier, which wets everything under it. The Kids Line Humidifier doesn't have this problem, the water tank doesn't leak water when it's turned upside down.

Read Best Reviews of Kids Line Ultrasonic Cool Mist Humidifier Here

I was hesitant initially to purchase this item based on the mixed reviews but after buying it I'm so happy I did. I love this humidifier! I've used it daily since 12/1/12. Some highlights:

PRO's

1. It fits the jungle theme perfectly in my newborn's bedroom and the humidifier works great. So far I've only used this in my living room which is approximately 500 600 sq ft. It gets refilled 2-3 x's to keep my humidity between 35% 40% ( 20% without use) will vary depending on room size and desired humidity level.

2. No filters! I have hard water so I have followed the instructions to soak in vinegar (left for 1 hr instead of 20 min bc I got sidetracked). Only soaking 1x per week rather than daily; haven't noticed any effect. Note: I considered using bleach but would imagine this would deteriorate the water seal. Just follow the provided instructions to use vinegar!! See note for product in Con #1 if you're concerned with bacteria.

3. The 360 degree mist. Comes out of each ear and the top of the monkey's head. Have not had leaks like other reviewers -I have had it sitting on a cheap, 12-in round pan just to ensure no damage to the wood stand it was on.

CON's:

1) Can't reach inside of water tub to scrub out. I would use my Holmes Humidifier Bacteriostat solution but I don't think it's necessary since the water doesn't sit for an extended period.

2) Manual functions no digital display or timer. NOT a big deal. I decided to buy the Acu-Rite Home Comfort Monitor from Amazon and love it! Monitors the humidity level accurately and saved me money not having to spend more for a built in humidistat.

One additional note: My allergist informed me that dust mites cannot survive above 40% humidity (I am highly allergic). Keep this in mind when humidifying the intended space for your child. My humidistat ensures that I stay within a comfortable 30-40% level.

The con's had no impact for me, therefore, I gave this adorable monkey a 5 star review. If anything changes, I will come back to provide an update.

Want Kids Line Ultrasonic Cool Mist Humidifier Discount?

I love this humidifier. First off, it's super cute it my son's nautical nursery. Second, I love that there is no filters for this. I've been using a Vick's humidifer that works great however, the filters make it expensive. We now use this in our room which we don't use every night like we do for my son. The humidifier needs to be cleaned monthly or every other month (we prefer monthly but could go longer). The only downside is that you have to fill the water often. We only run ours at night but by morning it's empty however, you can definetly tell that its doing its job as opposed to our Vick's. Our Vick's one lasts through the night and a little longer but I am not sure it works as hard as this one. I am very pleased with it and does its job for our purpose. If you want a humidifier that lasts for more extended period of time than this isn't your humidifier.

Save 15% Off

Honeywell HCM-890B - Humidifier - black

It seems to work good ( just got today) but sure is louder than i thought would be, if in same room as TV then you have to turn up TV about 4 or 5 notches

I got this for Xmas after asking for one because my apartment is so dry during the cold winter months. I love that it's black and matches the living room. It does the job and works great. The only thing I don't like about it is that it is noisy to the point where the television has to be turned up to block it out.

Buy Honeywell HCM-890B - Humidifier - black Now

I've been looking in stores & on-line for a small humidifier for my small living room. It arrived fast & in white instead of the black in the photo, but the same otherwise. I looked at the box b/4 opening & figured it to be a bit small for a 1 gallon tank... Welp, I got had! It states it's "2 gal output a day", NOT a 2 gallon tank. It is a 1 gallon tank that you must fill 2 times a day!?!? Really? Sadly, I looked back at all the other humidifiers I looked at (close in price)and they were all like this, stating a 'daily output' & not the actual tank size. All I'll say is be aware of that!! I did see these cute, colorful teardrop shaped ones for about $44, only 10 dollars more than I paid for this one. They clearly state a 2 gallon tank. I'm most likely going to keep this one for a few days & see how it works. If I return it, I'm buying a teardrop in pink! I can say for now that the high setting is very loud. I'm all for white noise, but this may be a bit much for most folks. Low is tolerable.

Read Best Reviews of Honeywell HCM-890B - Humidifier - black Here

Heard on the reviews that it is kind of loud which is exactly what I wanted/needed with my 1 year old. He is a light sleeper and this drowns out noise and keeps his room moist. He wakes up with his little curls in ringlettes. So darn cute!

Want Honeywell HCM-890B - Humidifier - black Discount?

The machine does not leak as so many complained in previous reviews. I suspect they did not have the container on tight. It must be on totally correctly. In addition, I am sure that people are using tap water for the container when the reviewer complains about the filter. I used bottled distilled water. It only costs about 85 cents a gallon and is worth the money for this and any other humidifier. The primary negative about the machine is that it is quite noisy. I use it in my bedroom but not if I am trying to watch TV. It is far too noisy for that. Even the low position is loud. The high position is really loud. For the money, it is not a bad purchase if consider the negatives not relevant.

Save 33% Off